Victron Argodiode 160-2AC 2 BAT 160A – battery isolator for charging two battery banksThe Victron Argodiode 160-2AC 2 BAT 160A is a battery isolator from Victron Energy that charges two battery banks from a single source. The banks are connected automatically during charging and separated again afterwards, ensuring the starter battery is never drained by consumption.Advantages
Automatic separation: Connects battery banks during charging and separates them again when charging stops.
Protects the starter battery: Power consumption cannot drain the starter battery, so the engine can always be started.
Simple installation: No programming required — the unit operates automatically based on voltage.
Applications
Charging a starter battery and a service battery from the same source.
Motorhomes and boats with two or more battery banks.
Simple installation without programming.
Specifications
Specification
Details
Rated voltage
6/12/24 V
Weight
1.3 kg
Dimensions (h × w × d)
150 × 120 × 60 mm
Item number
ARG160201020
Download datasheet (PDF)
Victron Lynx Smart BMS 500 NG (M10) – Battery management system for lithium batteriesThe Victron Lynx Smart BMS 500 NG (M10) is a battery management system (BMS) from Victron Energy for LiFePO4 batteries. It monitors the cells and intervenes with the charger, inverter, and MPPT before the battery can be damaged, and built-in Bluetooth makes it possible to monitor operation and change settings directly from the VictronConnect app.Benefits
Protects cells: Disconnects charging and discharging in case of excessively high or low cell voltage.
Controls the entire system: Sends a signal to the inverter, charger, and MPPT so they react before the battery is damaged.
For Victron LiFePO4: Designed for Victron Smart Lithium batteries and their cell balancing.
Bluetooth built-in: View cell voltages and status in the VictronConnect app.
Application
Protection of Victron LiFePO4 batteries against over- and undervoltage.
Lithium systems with inverter, charger, and MPPT from Victron.
Safe operation of lithium banks in boats and motorhomes.
Specifications
Specification
Details
Supply voltage range
9 – 60Vdc
Supported system voltages
12, 24, or 48V
Reverse polarity protection
No
Main safety contactor continuous current rating
500 A continuous
Main safety contactor peak current rating
600 A for 5 minutes
Power consumption OFF state
0.3 mA for all system voltages
Power consumption in Standby state
Approximately 0.6 W (50 mA at 12V)
Power consumption in ON state
Approximately 2.6 W (217 mA at 12V) depending on state of relays
Min. load resistance for pre-charging
10Ω and above for 12V systems / 20Ω and above for 24V and 48V systems
AUX output max. current rating
1.1 A continuous, protected by resettable fuse
Allow-to-charge port max. current rating
0.5 A at 60Vdc, protected by resettable fuse
Allow-to-discharge port max. current rating
0.5 A at 60Vdc, protected by resettable fuse
Programmable relay (SPDT) max. current rating
2 A at 60Vdc
Weight
2.2 kg
Technology
LITHIUM
Dimensions (h × w × d)
80 × 186 × 170 mm
Item number
LYN034160310
Download datasheet (PDF)
Victron Argodiode 140-3AC 3 BAT 140A – battery isolator for charging two battery banksThe Victron Argodiode 140-3AC 3 BAT 140A is a battery isolator from Victron Energy that allows charging of two battery banks from a single source. The banks are automatically connected during charging and separated again afterwards, ensuring the starter battery is never drained by the load.Advantages
Automatic separation: Connects the battery banks during charging and separates them again when charging stops.
Protects the starter battery: The load cannot drain the starter battery, so the engine can always be started.
Simple installation: No programming — the unit operates independently based on voltage.
Applications
Charging a starter battery and a service battery from the same source.
Camper vans and boats with two or more battery banks.
Simple installation without programming.
Specifications
Specification
Details
Nominal voltage
6/12/24 V
Weight
1.1 kg
Dimensions (h × w × d)
150 × 120 × 60 mm
Part number
ARG140301020R
Download datasheet (PDF)
Victron Argodiode 180-3AC 3 BAT 180A – battery isolator for charging three battery banksThe Victron Argodiode 180-3AC 3 BAT 180A is a battery isolator from Victron Energy that allows for charging three battery banks from a single source. The banks are automatically connected during charging and separated again afterwards, ensuring the starter battery is never drained by power consumption.Advantages
Automatic separation: Connects the battery banks during charging and separates them when charging stops.
Protects the starter battery: Power consumption cannot drain the starter battery, so the engine can always be started.
Simple installation: No programming required — the unit operates independently based on voltage.
Applications
Charging a starter battery and auxiliary batteries from the same source.
Camper vans and boats with two or more battery banks.
Simple installation without programming.
Specifications
Specification
Details
Rated voltage
6/12/24 V
Weight
1.6 kg
Dimensions (h × w × d)
200 × 120 × 60 mm
Part number
ARG180301020
Download datasheet (PDF)
Victron Argodiode 120-2AC 2 BAT 120A – battery isolator for charging two battery banksThe Victron Argodiode 120-2AC 2 BAT 120A is a battery isolator from Victron Energy that charges two battery banks from the same source. The banks are automatically connected during charging and separated again afterwards, so that the starter battery is never drained by the power consumption.Advantages
Automatic separation: Connects the battery banks during charging and separates them again when charging stops.
Protects the starter battery: Power consumption cannot drain the starter battery, so the engine can always be started.
Simple installation: No programming required — the unit operates automatically based on voltage.
Application
Charging a starter battery and a service battery from the same source.
Camper vans and boats with two or more battery banks.
Simple installation without programming.
Specifications
Specification
Details
Nominal voltage
6/12/24 V
Weight
1 kg
Dimensions (h × w × d)
115 × 120 × 60 mm
Part number
ARG120201020R
Download datasheet (PDF)
Victron Argodiode 100-3AC 3 BAT 100A – battery isolator for charging two battery banksThe Victron Argodiode 100-3AC 3 BAT 100A is a battery isolator from Victron Energy that allows charging two battery banks from a single source. The banks are automatically connected during charging and separated again afterwards, ensuring the starter battery is never drained by the load.Advantages
Automatic splitting: Connects the battery banks during charging and disconnects them when charging stops.
Protects the starter battery: The load cannot drain the starter battery, ensuring the engine can always be started.
Simple installation: No programming required — the unit operates independently based on voltage.
Applications
Charging a starter battery and a service battery from the same source.
Camper vans and boats with two or more battery banks.
Simple installation without programming.
Specifications
Specification
Details
Nominal voltage
6/12/24 V
Weight
1 kg
Dimensions (h × w × d)
115 × 120 × 60 mm
Item number
ARG100301000R
Download datasheet (PDF)
Victron Lynx Smart BMS 500 (M10) – battery management system for lithium batteriesThe Victron Lynx Smart BMS 500 (M10) is a battery management system (BMS) from Victron Energy for LiFePO4 batteries. It monitors the cells and intervenes with the charger, inverter, and MPPT before the battery can be damaged, and built-in Bluetooth makes it possible to monitor operation and change settings directly from the VictronConnect app.Advantages
Protects the cells: Disconnects charging and consumption in case of excessively high or low cell voltage.
Controls the entire system: Sends a signal to the inverter, charger, and MPPT so they react before the battery is damaged.
For Victron LiFePO4: Designed for Victron Smart Lithium batteries and their cell balancing.
Built-in Bluetooth: View cell voltages and status in the VictronConnect app.
Application
Protection of Victron LiFePO4 batteries against over- and undervoltage.
Lithium systems with inverter, charger, and MPPT from Victron.
Safe operation of lithium banks in boats and motorhomes.
Specifications
Specification
Details
Supply voltage range
9 – 60Vdc
Supported system voltages
12, 24, or 48V
Reverse polarity protection
No
Main safety contactor continuous current rating
500 A continuous
Main safety contactor peak current rating
600 A for 5 minutes
Power consumption OFF state
0.3 mA for all system voltages
Power consumption in Standby state
Approximately 0.6 W (50 mA at 12V)
Power consumption in ON state
Approximately 2.6 W (217 mA at 12V) depending on state of relays
Min. load resistance for pre-charge
10Ω and above for 12V systems / 20Ω and above for 24V and 48V systems
AUX output max. current rating
1.1 A continuous, protected by resettable fuse
Allow-to-charge port max. current rating
0.5 A at 60Vdc, protected by resettable fuse
Allow-to-discharge port max. current rating
0.5 A at 60Vdc, protected by resettable fuse
Programmable relay (SPDT) max. current rating
2 A at 60Vdc
Weight
2.2 kg
Technology
LITHIUM
Dimensions (h × w × d)
80 × 186 × 170 mm
Item number
LYN034160210
Download datasheet (PDF)
Victron Lynx Smart BMS 1000 NG (M10) – battery management system for lithium batteriesThe Victron Lynx Smart BMS 1000 NG (M10) is a battery management system (BMS) from Victron Energy for LiFePO4 batteries. It monitors the cells and intervenes with the charger, inverter, and MPPT before the battery can be damaged, and built-in Bluetooth makes it possible to monitor operation and change settings directly from the VictronConnect app.Advantages
Protects the cells: Disconnects charging and consumption in the event of too high or too low cell voltage.
Controls the entire system: Sends a signal to the inverter, charger, and MPPT so they react before the battery is damaged.
For Victron LiFePO4: Designed for Victron Smart Lithium batteries and their cell balancing.
Bluetooth built-in: View cell voltages and status in the VictronConnect app.
Application
Protection of Victron LiFePO4 batteries against over- and undervoltage.
Lithium systems with inverters, chargers, and MPPT from Victron.
Safe operation of lithium banks in boats and motorhomes.
Specifications
Specification
Details
Supply voltage range
9 – 60Vdc
Supported system voltages
12, 24, or 48V
Reverse polarity protection
No
Main safety contactor continuous current rating
500 A continuous
Main safety contactor peak current rating
600 A for 5 minutes
Power consumption OFF state
0.3 mA for all system voltages
Power consumption in Standby state
Approximately 0.6 W (50 mA at 12V)
Power consumption in ON state
Approximately 2.6 W (217 mA at 12V) depending on state of relays
Min. consumption resistance for pre-charging
10Ω and above for 12V systems / 20Ω and above for 24V and 48V systems
AUX output max. current rating
1.1 A continuous, protected by resettable fuse
Allow-to-charge port max. current rating
0.5 A at 60Vdc, protected by resettable fuse
Allow-to-discharge port max. current rating
0.5 A at 60Vdc, protected by resettable fuse
Programmable relay (SPDT) max. current rating
2 A at 60Vdc
Weight
1.4 kg
Technology
LITHIUM
Dimensions (h × w × d)
80 × 186 × 170 mm
Item number
LYN034170310
Download datasheet (PDF)
Victron Lynx Smart BMS 500 (M8) – Battery Management System for lithium batteriesThe Victron Lynx Smart BMS 500 (M8) is a battery management system (BMS) from Victron Energy for LiFePO4 batteries. It monitors the cells and intervenes with the charger, inverter, and MPPT before the battery can be damaged, and built-in Bluetooth makes it possible to monitor operation and change settings directly from the VictronConnect app.Advantages
Protects the cells: Disconnects charging and consumption in the event of high or low cell voltage.
Controls the entire system: Sends a signal to the inverter, charger, and MPPT so they react before the battery is damaged.
For Victron LiFePO4: Designed for Victron Smart Lithium batteries and their cell balancing.
Bluetooth built-in: View cell voltages and status in the VictronConnect app.
Applications
Protection of Victron LiFePO4 batteries against over- and under-voltage.
Lithium systems with inverter, charger, and MPPT from Victron.
Safe operation of lithium banks in boats and motorhomes.
Specifications
Specification
Details
Supply voltage range
9 – 60Vdc
Supported system voltages
12, 24, or 48V
Reverse polarity protection
No
Main safety contactor continuous current rating
500 A continuous
Main safety contactor peak current rating
600 A for 5 minutes
Power consumption OFF state
0.3 mA for all system voltages
Power consumption in Standby state
Approximately 0.6 W (50 mA at 12V)
Power consumption in ON state
Approximately 2.6 W (217 mA at 12V) depending on state of relays
Min. consumption resistance for pre-charging
10Ω and above for 12V systems / 20Ω and above for 24V and 48V systems
AUX output max. current rating
1.1 A continuous, protected by resettable fuse
Allow-to-charge port max. current rating
0.5 A at 60Vdc, protected by resettable fuse
Allow-to-discharge port max. current rating
0.5 A at 60Vdc, protected by resettable fuse
Programmable relay (SPDT) max. current rating
2 A at 60Vdc
Weight
2.19 kg
Technology
LITHIUM
Dimensions (h × w × d)
90 × 30 × 100 mm
Item number
LYN034160200
Download datasheet (PDF)
Victron Lynx Smart BMS 1000 – battery management system for lithium batteriesThe Victron Lynx Smart BMS 1000 is a battery management system (BMS) from Victron Energy for LiFePO4 batteries. It monitors the cells and intervenes with the charger, inverter, and MPPT before the battery can be damaged, and built-in Bluetooth makes it possible to monitor operation and change settings directly from the VictronConnect app.Advantages
Protects the cells: Disconnects charging and discharging in the event of over- or undervoltage in the cells.
Controls the entire system: Sends signals to the inverter, charger, and MPPT so they react before the battery is damaged.
For Victron LiFePO4: Designed for Victron Smart Lithium batteries and their cell balancing.
Bluetooth built-in: View cell voltages and status in the VictronConnect app.
Applications
Protection of Victron LiFePO4 batteries against over- and undervoltage.
Lithium systems with inverters, chargers, and MPPTs from Victron.
Safe operation of lithium banks in boats and motorhomes.
Specifications
Specification
Details
Supply voltage range
9 – 60Vdc
Supported system voltages
12, 24, or 48V
Reverse polarity protection
No
Main safety contactor continuous current rating
500 A continuous
Main safety contactor peak current rating
600 A for 5 minutes
Power consumption OFF mode
0.3 mA for all system voltages
Power consumption in Standby mode
Approximately 0.6 W (50 mA at 12V)
Power consumption in ON mode
Approximately 2.6 W (217 mA at 12V) depending on state of relays
Min. load resistance for pre-charge
10Ω and above for 12V systems / 20Ω and above for 24V and 48V systems
AUX output max. current rating
1.1 A continuous, protected by resettable fuse
Allow-to-charge port max. current rating
0.5 A at 60Vdc, protected by resettable fuse
Allow-to-discharge port max. current rating
0.5 A at 60Vdc, protected by resettable fuse
Programmable relay (SPDT) max. current rating
2 A at 60Vdc
Weight
2.5 kg
Technology
LITHIUM
Dimensions (h × w × d)
170 × 80 × 186 mm
Item number
LYN034170210
Download datasheet (PDF)
Victron Lynx Shunt VE.Can (M10) – original Victron accessoryThe Victron Lynx Shunt VE.Can (M10) is an original accessory from Victron Energy. It integrates directly into the Victron system and is built to last in demanding marine and vehicle environments.Benefits
Original Victron accessory: Fits the Victron system directly without any adjustments.
Reliable quality: Materials and workmanship built to endure in marine and vehicle environments.
Application
Original accessory that fits the Victron system directly.
Camper van, boat, summer cottage, and off-grid systems.
Safe and operationally stable installation.
Specifications
Specification
Details
Supported system voltages
12, 24, or 48V
Reverse polarity protection
No
Current rating
1000 Adc continuous
Power consumption
60 mA @ 12V / 33 mA @ 24V / 20 mA @ 48V
Potential free alarm contact
3 A, 30 Vdc, 250 Vac
Supply voltage range
9 - 70 Vdc
Busbar
M10
Fuse or fuse dummy
M8 (a Mega fuse can be installed on M6 bolts)
VE.Can
RJ45 and RJ45 terminator
Power supply connection to Lynx Distributor
RJ10 (a RJ10 cable ships with each Lynx Distributor)
Temperature sensor
terminal connector (sensor included)
Relay
screw terminal
Enclosure material
ABS
Enclosure dimensions (hxwxd)
190 × 180 × 80 mm
Unit weight
1.4 kg
Busbar material
Tinned copper
Busbar dimensions (hxw)
8 × 30 mm
Operating temperature range
-40 °C to +60 °C
Storage temperature
-40 °C to +60 °C
Humidity
max. 95% (non-condensing)
Protection class
IP22
Dimensions (h × w × d)
80 × 186 × 170 mm
Item number
LYN040102110
Download datasheet (PDF)
Victron VE Transfer switch 5KVA/230V – automatic transfer switch between two AC sourcesThe Victron VE Transfer Switch 5 kVA is an automatic transfer switch with two AC inputs and one output. The loads are supplied from input 1 (e.g. shore power or a generator), and if this supply fails or goes outside the voltage or frequency limits, the switch automatically changes over to input 2 – typically an inverter. During the switchover itself, the power is briefly interrupted, so sensitive electronics such as computers may lose data.Benefits
Automatic switching: Switches between the two sources without manual operation.
Delayed switch-back: Once input 1 has been stable for approx. 10 seconds (adjustable), it switches back – this protects your equipment during short voltage dips.
20 A per input: Rated current of 20 A on both inputs and the output, and motor loads (e.g. air conditioning) of up to 1.3 kW.
Auxiliary contact: Together with a MultiPlus and a Digital Multi Control, it can automatically switch the current limit to a preset generator value.
Applications
Switching between generator and shore power in boats or motorhomes.
Switching between inverter and generator or shore power.
Giving a MultiPlus access to two AC sources instead of one.
Specifications
Specification
Details
Nominal voltage
200–250 V AC, single-phase
Nominal frequency
50–60 Hz
Rated current, input 1 and 2
20 A
Rated output current
20 A
Max. motor load (e.g. air conditioning)
1.3 kW
Self-consumption, input 1
6 VA
Switching time, closing contacts
10–20 ms
Switching time, opening contacts
5–20 ms
Delay, input 1
Approx. 10 s (adjustable)
Auxiliary contact
200–240 V AC, 20 A, cos φ = 1
Operating temperature range
-5 to +60 °C
Humidity
Max. 95% (non-condensing)
Circuit breaker (MCB) and residual current device (RCD)
Not included – depends on the installation
Enclosure rating
IP54
Colour
RAL 7035
Dimensions
175 × 215 × 120 mm
Weight
1.85 kg
Item number
COS230502100
Download manual (PDF)
Victron Class-T Power In (M10) – power distribution and fusingThe Victron Class-T Power In (M10) is a genuine Victron component for DC power distribution and fusing. It protects cables and components against overcurrent and makes the installation organized and easy to service.Benefits
Secure fusing: Protects cables and components against overcurrent and short circuits.
Organized installation: Consolidates distribution in one place, making the system easy to service.
Genuine Victron quality: Fits directly into Lynx and Victron systems.
Application
Secure distribution and fusing of DC power.
Camper vans, boats, and off-grid systems.
Organized and service-friendly installation.
Specifications
Specification
Details
Rated voltage
6/12/24 V
Weight
2.3 kg
Dimensions (h × w × d)
170 × 97 × 280 mm
Part number
LYN060404010
Victron Isolation transformer 4500W 115/230V – galvanic isolation of shore powerThe Victron Isolation transformer 4500W 115/230V from Victron Energy provides galvanic isolation between shore power and the onboard installation. It stops galvanic corrosion on the hull and makes the shore connection safe.Advantages
Galvanic isolation: Breaks the connection to the harbor ground and stops galvanic corrosion on the hull.
Safe shore power: Protects both the installation and people in case of faults in the harbor grid.
Robust construction: Built for permanent operation in a humid environment.
Application
Shore power in boats, where galvanic corrosion must be avoided.
Adjustment between different grid voltages.
Safe separation of the vessel and the harbor grid.
Specifications
Specification
Details
AC input voltage
115 or 230 V
AC output
120 or 240 V
Frequency
50/60 Hz
Output current rating
17 A (115 V) / 8.5 A (230 V)
Soft start
Yes
Operating temperature range
-20 °C to 40 °C
Humidity
max. 95%, non-condensing
Transformer type
Toroidal (low noise, low weight), 1:1.05 ratio
Enclosure
aluminium (blue RAL 5012)
Protection class
IP21
Safety
EN 60076
Weight
12.7 kg
Dimensions (h × w × d)
375 × 214 × 135
Item number
ITR040452042
Download datasheet (PDF)
Victron Isolation Transformer 3600W 115/230V – galvanic isolation of shore powerThe Victron Isolation Transformer 3600W 115/230V from Victron Energy provides galvanic isolation between shore power and the onboard installation. It stops galvanic corrosion on the hull and makes the shore connection safe.Advantages
Galvanic isolation: Breaks the connection to the harbor's ground and stops galvanic corrosion on the hull.
Safe shore power: Protects both the system and personnel in case of faults in the harbor's grid.
Robust construction: Built for continuous operation in a humid environment.
Application
Shore power in boats where galvanic corrosion must be avoided.
Adjustment between different grid voltages.
Safe separation of the vessel and the harbor grid.
Specifications
Specification
Details
AC input voltage
115 or 230 V
AC output
120 or 240 V
Frequency
50/60 Hz
Output current rating
17 A (115 V) / 8.5 A (230 V)
Soft start
Yes
Operating temperature range
-20 °C to 40 °C
Humidity
max. 95%, non-condensing
Transformer type
Toroidal (low noise, low weight), 1:1.05 ratio
Enclosure
aluminum (blue RAL 5012)
Protection class
IP21
Safety
EN 60076
Weight
12.7 kg
Dimensions (h × w × d)
375 × 214 × 135
Part number
ITR040362042
Download datasheet (PDF)
Victron VE Transfer switch 10KVA/230V – automatic transfer switch between two AC sourcesThe Victron VE Transfer Switch 10 kVA is an automatic transfer switch with two AC inputs and one output. The loads are supplied from input 1 (e.g. shore power or a generator), and if this supply fails or goes outside the voltage or frequency limits, the switch automatically changes over to input 2 – typically an inverter. During the switchover itself, the power is briefly interrupted, so sensitive electronics such as computers may lose data.Benefits
Automatic switching: Switches between the two sources without manual operation.
Delayed switch-back: Once input 1 has been stable for approx. 10 seconds (adjustable), it switches back – this protects your equipment during short voltage dips.
40 A per input: Rated current of 40 A on both inputs and the output, and motor loads (e.g. air conditioning) of up to 8 kW.
Auxiliary contact: Together with a MultiPlus and a Digital Multi Control, it can automatically switch the current limit to a preset generator value.
Applications
Switching between generator and shore power in boats or motorhomes.
Switching between inverter and generator or shore power.
Giving a MultiPlus access to two AC sources instead of one.
Specifications
Specification
Details
Nominal voltage
200–250 V AC, single-phase
Nominal frequency
50–60 Hz
Rated current, input 1 and 2
40 A
Rated output current
40 A
Max. motor load (e.g. air conditioning)
8 kW
Self-consumption, input 1
6 VA
Switching time, closing contacts
10–20 ms
Switching time, opening contacts
5–20 ms
Delay, input 1
Approx. 10 s (adjustable)
Auxiliary contact
200–240 V AC, 20 A, cos φ = 1
Operating temperature range
-5 to +60 °C
Humidity
Max. 95% (non-condensing)
Circuit breaker (MCB) and residual current device (RCD)
Not included – depends on the installation
Enclosure rating
IP54
Colour
RAL 7035
Dimensions
175 × 215 × 120 mm
Weight
1.65 kg
Item number
COS230103100
Download manual (PDF)
Victron Isolation transformer 8000W 230V – galvanic isolation of shore powerThe Victron Isolation transformer 8000W 230V from Victron Energy provides galvanic isolation between shore power and the onboard installation. It stops galvanic corrosion on the hull and makes the shore connection safe.Advantages
Galvanic isolation: Breaks the connection to the harbor ground and stops galvanic corrosion on the hull.
Safe shore power: Protects both systems and people in case of faults in the harbor grid.
Robust construction: Built for permanent operation in a humid environment.
Application
Shore power in boats where galvanic corrosion must be avoided.
Adaptation between different grid voltages.
Safe isolation of ship and harbor grid.
Specifications
Specification
Details
Weight
28 kg
Dimensions (h × w × d)
243 × 258 × 362 mm
Part number
ITR000802002
Download datasheet (PDF)
Victron Isolation transformer 7000W 230V – galvanic isolation of shore powerThe Victron Isolation transformer 7000W 230V from Victron Energy provides galvanic isolation between shore power and the onboard installation. It stops galvanic corrosion on the hull and makes the shore connection safe.Advantages
Galvanic isolation: Breaks the connection to the harbor's earth and stops galvanic corrosion on the hull.
Safe shore power: Protects both the system and personnel in case of faults in the harbor grid.
Robust construction: Built for permanent operation in a humid environment.
Application
Shore power in boats where galvanic corrosion must be avoided.
Adjustment between different mains voltages.
Safe isolation of the vessel and the harbor grid.
Specifications
Specification
Details
Nominal voltage
6/12/24 V
Weight
30 kg
Dimensions (h × w × d)
218 × 258 × 362 mm
Item number
ITR000702001
Download datasheet (PDF)
Victron Isolation transformer 2500W 115/230V – galvanic isolation of shore powerThe Victron Isolation transformer 2500W 115/230V from Victron Energy provides galvanic isolation between shore power and the onboard installation. It stops galvanic corrosion on the hull and makes the shore connection safe.Advantages
Galvanic isolation: Breaks the connection to the harbor ground and stops galvanic corrosion on the hull.
Safe shore power: Protects both the system and people in the event of a fault in the harbor grid.
Robust construction: Built for permanent operation in a humid environment.
Application
Shore power in a boat where galvanic corrosion must be avoided.
Adaptation between different grid voltages.
Safe separation of the ship and the harbor grid.
Specifications
Specification
Details
AC input voltage
115 or 230 V
AC output
120 or 240 V
Frequency
50/60 Hz
Output current rating
17 A (115 V) / 8.5 A (230 V)
Soft start
Yes
Operating temperature range
-20 °C to 40 °C
Humidity
max. 95%, non-condensing
Transformer type
Toroidal (low noise, low weight), 1:1.05 ratio
Enclosure
aluminium (blue RAL 5012)
Protection class
IP21
Safety
EN 60076
Weight
12.7 kg
Dimensions (h × w × d)
375 × 214 × 135
Item number
ITR040252043
Download datasheet (PDF)
Victron Isolation transformer 2000W 115/230V – galvanic isolation of shore powerThe Victron Isolation transformer 2000W 115/230V from Victron Energy provides galvanic isolation between shore power and the onboard installation. It stops galvanic corrosion on the hull and makes the shore connection safe.Benefits
Galvanic isolation: Breaks the connection to the shore ground and stops galvanic corrosion on the hull.
Safe shore power: Protects both the system and people in the event of faults in the shore grid.
Robust construction: Built for permanent operation in a humid environment.
Application
Shore power in boats where galvanic corrosion must be avoided.
Matching between different mains voltages.
Safe isolation of the vessel from the shore grid.
Specifications
Specification
Details
AC input voltage
115 or 230 V
AC output
120 or 240 V
Frequency
50/60 Hz
Output current rating
17 A (115 V) / 8.5 A (230 V)
Soft start
Yes
Operating temperature range
-20 °C to 40 °C
Humidity
max. 95%, non-condensing
Transformer type
Toroidal (low noise, low weight), 1:1.05 ratio
Enclosure
aluminium (blue RAL 5012)
Protection class
IP21
Safety
EN 60076
Weight
12.7 kg
Dimensions (h × w × d)
375 × 214 × 135
Rated voltage
6/12/24 V
Item number
ITR040202041
Download datasheet (PDF)
Victron Isolation transformer 4500W Auto 115/230 – galvanic isolation of shore powerThe Victron Isolation transformer 4500W Auto 115/230 from Victron Energy provides galvanic isolation between shore power and the onboard installation. It stops galvanic corrosion on the hull and makes the shore connection safe.Advantages
Galvanic isolation: Breaks the connection to the harbor's ground and stops galvanic corrosion on the hull.
Safe shore power: Protects both systems and people in the event of faults in the harbor grid.
Robust construction: Built for continuous operation in a humid environment.
Application
Shore power in a boat where galvanic corrosion must be avoided.
Adaptation between different mains voltages.
Safe separation of the vessel and the harbor grid.
Specifications
Specification
Details
AC input voltage
115 or 230 V, automatic detection
AC output
120 or 240 V
Frequency
50/60 Hz
Output current rating
38 A (115 V) / 19 A (230 V)
Soft start
Yes
Operating temperature range
-20 °C to 40 °C
Humidity
max. 95%, non-condensing
Transformer type
Toroidal (low noise, low weight), 1:1.05 ratio
Enclosure
aluminum (blue RAL 5012)
Protection class
IP21
Safety
EN 60076
Weight
21.8 kg
Dimensions (h × w × d)
362 × 258 × 221
Item number
ITR050452042
Download datasheet (PDF)
Victron Galvanic Isolator VDI-64 A – galvanic isolation of shore powerThe Victron Galvanic Isolator VDI-64 A from Victron Energy provides galvanic isolation between shore power and the onboard installation. It stops galvanic corrosion of the hull and makes the shore connection safe.Advantages
Galvanic isolation: Breaks the connection to the shore ground and stops galvanic corrosion of the hull.
Safe shore power: Protects both systems and persons in case of faults in the shore grid.
Robust construction: Built for permanent operation in a humid environment.
Application
Shore power in boats where galvanic corrosion must be avoided.
Adaptation between different grid voltages.
Safe isolation of the vessel and the shore grid.
Specifications
Specification
Details
Nominal voltage
6/12/24 V
Weight
2 kg
Dimensions (h × w × d)
224 × 164 × 64 mm
Item number
GDI000064000
Download datasheet (PDF)
Victron Isolation transformer 3600W 115/230V – galvanic isolation from shore powerThe Victron Isolation transformer 3600W 115/230V from Victron Energy provides galvanic isolation between shore power and the onboard installation. It stops galvanic corrosion on the hull and makes the shore connection safe.Advantages
Galvanic isolation: Breaks the connection to the harbor's ground and stops galvanic corrosion on the hull.
Safe shore power: Protects both systems and people in the event of faults in the harbor's power grid.
Robust construction: Built for permanent operation in a humid environment.
Application
Shore power in a boat where galvanic corrosion must be avoided.
Adjustment between different mains voltages.
Safe separation of vessel and harbor power grid.
Specifications
Specification
Details
AC input voltage
115 or 230 V
AC output
120 or 240 V
Frequency
50/60 Hz
Output current rating
17 A (115 V) / 8.5 A (230 V)
Soft start
Yes
Operating temperature range
-20 °C to 40 °C
Humidity
max. 95%, non-condensing
Transformer type
Toroidal (low noise, low weight), 1:1.05 ratio
Enclosure
aluminum (blue RAL 5012)
Protection class
IP21
Safety
EN 60076
Weight
12.7 kg
Dimensions (h × w × d)
375 × 214 × 135
Nominal voltage
6/12/24 V
Item number
ITR040362041
Download datasheet (PDF)
Victron Galvanic Isolator VDI-32 A – galvanic isolation of shore powerThe Victron Galvanic Isolator VDI-32 A from Victron Energy provides galvanic isolation between shore power and the onboard installation. It stops galvanic corrosion on the hull and makes the shore connection safe.Advantages
Galvanic isolation: Breaks the connection to the marina's earth and stops galvanic corrosion on the hull.
Safe shore power: Protects both systems and personnel in case of faults in the marina's grid.
Robust construction: Built for permanent operation in a humid environment.
Application
Shore power in boats where galvanic corrosion must be avoided.
Adaptation between different grid voltages.
Safe separation of vessel and the marina's grid.
Specifications
Specification
Details
Nominal voltage
6/12/24 V
Weight
2.1 kg
Dimensions (h × w × d)
235 × 164 × 63 mm
Item number
GDI000032000
Download datasheet (PDF)
Victron Galvanic Isolator VDI-16 A – galvanic isolation of shore powerThe Victron Galvanic Isolator VDI-16 A from Victron Energy provides galvanic isolation between shore power and the onboard installation. It stops galvanic corrosion on the hull and makes the shore connection safe.Advantages
Galvanic isolation: Breaks the connection to the harbor's ground and stops galvanic corrosion on the hull.
Safe shore power: Protects both the system and people in the event of faults in the harbor's power grid.
Robust construction: Built for continuous operation in a humid environment.
Application
Shore power in boats where galvanic corrosion must be avoided.
Matching between different mains voltages.
Safe separation of the vessel and the harbor's power grid.
Specifications
Specification
Details
Rated voltage
6/12/24 V
Weight
1.6 kg
Dimensions (h × w × d)
200 × 120 × 60 mm
Part number
GDI000016000
Download datasheet (PDF)
Victron Autotransformer 120/240 VAC-32A – galvanic isolation of shore powerThe Victron Autotransformer 120/240 VAC-32A from Victron Energy provides galvanic isolation between shore power and the onboard installation. It stops galvanic corrosion on the hull and makes the shore connection safe.Advantages
Galvanic isolation: Breaks the connection to the harbor ground and stops galvanic corrosion on the hull.
Safe shore power: Protects both the system and personnel in case of faults in the harbor grid.
Robust construction: Built for continuous operation in a humid environment.
Application
Shore power in boats where galvanic corrosion must be avoided.
Matching different grid voltages.
Safe isolation of the vessel and the harbor grid.
Specifications
Specification
Details
Input/output voltage
120 / 240 V
Input Circuit Breaker
50 A, Two Pole
Frequency
50/60 Hz
Max. 240 V Feed Through current
50 A
Neutral current, 30 min.
55 A @ 40 °C/100°F
Neutral current, Continuous
45 A @ 40 °C/100°F
Transformer type
Toroidal
Enclosure
Aluminum
Electrical terminals
screw terminals 35 mm² / AWG
Protection class
IP21
Safety
EN 60076
Weight
12.5 kg
Dimensions (h × w × d)
460 × 214 × 110 mm
Nominal voltage
6/12/24 V
Item number
ITR000100001
Download datasheet (PDF)
Victron Filax-2 110V/50 Hz-120V/60 Hz – ultra-fast automatic transfer switch for sensitive loadsThe Victron Filax-2 is an ultra-fast automatic AC transfer switch. Normally, the loads are supplied from a priority source such as the grid, shore power or a generator; if the voltage or frequency falls outside the limits, the Filax-2 switches over to an alternative source – typically an inverter – within a maximum of 16 ms, so computers and other sensitive electronics can keep running without interruption. It is not intended for large household appliances such as washing machines or electric motors. This version is for 110 V/50 Hz and 120 V/60 Hz installations – for standard Danish 230 V systems, you need the 230 V version.Benefits
Ultra-fast switching: Switches between the sources within a maximum of 16 ms.
Monitors voltage and frequency: Switches to the alternative source if the voltage on the priority source is too low or its frequency is too low/high.
Automatic switch-back: Switches back to the priority source once it has been within the limits for 30 seconds.
Robust enclosure: IP65 ABS enclosure for operation from -20 to +50 °C.
Applications
Computers, network equipment and industrial controls that must not restart during a power failure.
Entertainment electronics in boats or motorhomes when switching between shore power/generator and inverter.
Fixed installations where an inverter provides backup for sensitive loads.
Specifications
Specification
Details
Nominal voltage and frequency
110 V/50 Hz and 120 V/60 Hz
Max. current
16 A
Max. switching time (both directions)
16 ms
Priority source: switch at low voltage
88 V AC (50 Hz) / 90 V AC (60 Hz)
Priority source: switch back at voltage above
92 V AC (50 Hz) / 94 V AC (60 Hz)
Priority source: switch at low frequency
45 Hz (50 Hz grid) / 46 Hz (60 Hz grid)
Max. continuous input voltage (both sources)
130 V AC
Switch-back delay
30 s
Operating temperature range
-20 to +50 °C
Humidity
Max. 95% (non-condensing)
Enclosure
ABS, RAL 7035 (light grey)
Enclosure rating
IP65
Dimensions (h × w × d)
120 × 255 × 75 mm
Weight
0.8 kg
Item number
SDFI0000110
Download datasheet (PDF)
Victron Filax-2 230V/50 Hz-240V/60 Hz – ultra-fast automatic transfer switch for sensitive loadsThe Victron Filax-2 is an ultra-fast automatic AC transfer switch. Normally, the loads are supplied from a priority source such as the grid, shore power or a generator; if the voltage or frequency falls outside the limits, the Filax-2 switches over to an alternative source – typically an inverter – within a maximum of 16 ms, so computers and other sensitive electronics can keep running without interruption. It is not intended for large household appliances such as washing machines or electric motors. This version is for 230 V/50 Hz and 240 V/60 Hz installations.Benefits
Ultra-fast switching: Switches between the sources within a maximum of 16 ms.
Monitors voltage and frequency: Switches to the alternative source if the voltage on the priority source is too low or its frequency is too low/high.
Automatic switch-back: Switches back to the priority source once it has been within the limits for 30 seconds.
Robust enclosure: IP65 ABS enclosure for operation from -20 to +50 °C.
Applications
Computers, network equipment and industrial controls that must not restart during a power failure.
Entertainment electronics in boats or motorhomes when switching between shore power/generator and inverter.
Fixed installations where an inverter provides backup for sensitive loads.
Specifications
Specification
Details
Nominal voltage and frequency
230 V/50 Hz and 240 V/60 Hz
Max. current
16 A
Max. switching time (both directions)
16 ms
Priority source: switch at low voltage
180 V AC
Priority source: switch back at voltage above
188 V AC
Priority source: switch at low frequency
45 Hz (50 Hz grid) / 46 Hz (60 Hz grid)
Max. continuous input voltage (both sources)
260 V AC
Switch-back delay
30 s
Operating temperature range
-20 to +50 °C
Humidity
Max. 95% (non-condensing)
Enclosure
ABS, RAL 7035 (light grey)
Enclosure rating
IP65
Dimensions (h × w × d)
120 × 255 × 75 mm
Weight
0.8 kg
Item number
SDFI0000000
Download datasheet (PDF)
Victron Autotransformer 120/240 VAC-50A – galvanic isolation of shore powerThe Victron Autotransformer 120/240 VAC-50A from Victron Energy provides galvanic isolation between shore power and the onboard installation. It stops galvanic corrosion on the hull and makes the shore connection safe.Benefits
Galvanic isolation: Breaks the connection to the harbor's ground and stops galvanic corrosion on the hull.
Safe shore power: Protects both the system and people in the event of faults in the harbor grid.
Robust construction: Built for permanent operation in a humid environment.
Application
Shore power in boats where galvanic corrosion must be avoided.
Adaptation between different grid voltages.
Safe isolation of the vessel and the harbor grid.
Specifications
Specification
Details
Input/output voltage
120 / 240 V
Input Circuit Breaker
50 A, Two Pole
Frequency
50/60 Hz
Max. 240 V Feed Through current
50 A
Neutral current, 30 min.
55 A @ 40 °C/100°F
Neutral current, Continuous
45 A @ 40 °C/100°F
Transformer type
Toroidal
Enclosure
Aluminum
Electrical terminals
screw terminals 35 mm² / AWG
Protection class
IP21
Safety
EN 60076
Weight
12.5 kg
Dimensions (h × w × d)
460 × 214 × 110 mm
EAN
8719076066071
Item number
ITR000100052
Download datasheet (PDF)
Victron Anti-islanding box 63A 3-phase – original Victron accessoryThe Victron Anti-islanding box 63A 3-phase is an original accessory from Victron Energy. It integrates directly into the Victron system and is built to last in demanding marine and vehicle environments.Advantages
Original Victron accessory: Fits the Victron system directly without modification.
Reliable quality: Materials and workmanship designed to withstand marine and vehicle environments.
Application
Original accessory that fits directly into the Victron system.
Motorhomes, boats, summer cottages, and off-grid systems.
Safe and reliable installation.
Specifications
Specification
Details
Weight
3.185 kg
Dimensions (h × w × d)
100 × 380 × 230 mm
Part number
RCD000300200
Victron EasySolar-II 48/5000/70-50 GX – inverter and battery charger in one unitThe Victron EasySolar-II 48/5000/70-50 GX is a combined inverter and battery charger from Victron Energy — two functions in one unit. It provides the installation with pure sine wave 230V and switches automatically between shore power and battery operation.Benefits
PowerAssist and PowerControl: The unit supplements a weak shore connection with battery power and prevents the campsite fuse from blowing.
Automatic switch: Switches automatically between shore power and battery operation without interruption (50 A).
Pure sine wave: Same power quality as the electrical grid — even for sensitive electronics.
Built-in GX device: Full monitoring and remote control via the VRM Portal without additional hardware.
Application
Motorhomes and boats where both shore power and battery operation must be handled automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage in residential and commercial settings.
Specifications
Specification
Details
PowerControl and PowerAssist
Yes
Automatic switch
50 A
Max. AC input current
50 A
Auxiliary output
50 A
Input voltage range
38 – 66 V
Output in inverter mode
output voltage: 230 VAC ± 2 % Frequency: 50 Hz ± 0.1 %
Cont. output power at 25°C
5000 VA
Cont. output power at
3700 W
Cont. output power at 65°C
3000 W
Max. feed-in power
5000 VA
Peak power
9000 W
Max. efficiency
96 %
Zero-load consumption
18 W
AC input
input voltage range: 187-265 VAC input frequency: 45 – 65 Hz
Charge voltage absorption
57.6 V
Charge voltage float
55.2 V
Storage mode
52.8 V
Max. battery charge current
70 A
Battery temperature sensor
optional. Order number: ASS000001000
Programmable (AUX) relay
Yes
Auxiliary power supply
12V / 100 mA
Programmable open collector output
70 V / 100 mA
Temperature sensor
Yes
Analog-digital aux inputs
Yes, 2x
Voltage sense contacts
Yes
Protection
a - g
VE.Bus communication port
for parallel and three-phase operation, remote monitoring and system integration
General purpose communication port
Yes, 2x
Model
MPPT 250/100-Tr
Max. output current
100 A
Max. PV power
5800 W
Max. PV open circuit voltage
250 V
Self-consumption
20 mA
Interfaces
VE.Can, USB, Ethernet, VE.Direct, Wi-Fi
External AC current sensor (optional)
100 A
Remote on/off
Yes
Operating temperature range
-40 to +65 °C (fan-assisted cooling). Maximum Altitude 2000 m
Humidity (non-condensing)
max. 95 %
Material and color
steel, blue RAL 5012
Protection class
IP22
Battery connection
M8 bolts
230VAC connection
screw terminals 13 mm² (6 AWG)
Weight
31 kg
Dimensions (h × w × d)
565 × 323 × 148 mm
Safety
EN-IEC 62019-1, EN-IEC 6201-2, EN-IEC 60335-1, EN-IEC 60335-2-29
Emission / immunity
IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3
Uninterruptible power supply (UPS)
IEC 62040-1
Nominal voltage
48 V
Item number
PMP482507010
Download datasheet (PDF)
Victron Autotransformer 120/240 VAC-100A – galvanic isolation of shore powerThe Victron Autotransformer 120/240 VAC-100A from Victron Energy provides galvanic isolation between shore power and the onboard installation. It prevents galvanic corrosion on the hull and makes the shore connection safe.Advantages
Galvanic isolation: Breaks the connection to the harbor's ground and stops galvanic corrosion on the hull.
Safe shore power: Protects both systems and personnel in the event of faults in the harbor grid.
Robust construction: Built for permanent operation in a humid environment.
Applications
Shore power in boats where galvanic corrosion must be avoided.
Matching between different grid voltages.
Safe isolation of the vessel from the harbor grid.
Specifications
Specification
Details
Input/output voltage
120 / 240 V
Input Circuit Breaker
50 A, Two Pole
Frequency
50/60 Hz
Max. 240 V Feed Through current
50 A
Neutral current, 30 min.
55 A @ 40 °C/100°F
Neutral current, Continuous
45 A @ 40 °C/100°F
Transformer type
Toroidal
Enclosure
Aluminum
Electrical terminals
screw terminals 35 mm² / AWG
Protection class
IP21
Safety
EN 60076
Weight
12.5 kg
Dimensions (h × w × d)
460 × 214 × 110 mm
Nominal voltage
6/12/24 V
Part number
ITR000100101
Download datasheet (PDF)
Victron EasySolar-II GX 24V/3000W/70A-32 MPPT 250/70 – inverter and battery charger in one unitThe Victron EasySolar-II GX 24V/3000W/70A-32 MPPT 250/70 is a combined inverter and battery charger from Victron Energy — two functions in one unit. It supplies your installation with pure sine wave 230V and switches automatically between shore power and battery operation.Benefits
PowerAssist and PowerControl: The unit supplements a weak shore power connection with battery power and prevents the fuse at the campsite or marina from blowing.
Automatic transfer switch: Switches automatically between shore power and battery operation without interruption (32 A).
Pure sine wave: The same power quality as the mains grid — also for sensitive electronics.
Built-in GX device: Full monitoring and remote control via the VRM Portal without extra hardware.
Applications
Motorhomes and boats where both shore power and battery operation need to be handled automatically.
Off-grid and hybrid systems with solar panels and a generator.
Backup power systems and energy storage in homes and businesses.
Specifications
Specification
Details
PowerControl and PowerAssist
Yes
Transfer switch
32 A
Max. AC input current
32 A
Auxiliary output
32 A
Input voltage range
19 - 33 V
Output in inverter mode
Output voltage: 230 VAC ± 2% Frequency: 50 Hz ± 0.1%
Cont. output power at 25°C
3000 VA
Cont. output power at
2200 W
Cont. output power at 65°C
1700 W
Max. feed-back power
3000 VA
Peak power
5500 W
Max. efficiency
94 %
Zero-load power consumption
13 W
AC input
Input voltage range: 187-265 VAC Input frequency: 45 – 65 Hz
Charge voltage, absorption
28.8 V
Charge voltage, float
27.6 V
Storage mode
26.4 V
Max. battery charge current
70 A
Battery temperature sensor
Yes
Programmable (AUX) relay
Yes
Auxiliary power supply
12V / 100 mA
Programmable open collector output
70 V / 100 mA
Temperature sensor
Yes
Analogue/digital aux inputs
Yes, 2x
Voltage sense contacts
Yes
Protection
a - g
VE.Bus communication port
for parallel and three-phase operation, remote monitoring and system integration
General-purpose communication port
Yes, 2x
Model
MPPT 250/70-Tr
Max. output current
70 A
Max. PV power
2000 W
Max. PV open-circuit voltage
250 V
Own consumption
20 mA
Interfaces
VE.Can, USB, Ethernet, VE.Direct, Wi-Fi
External AC current sensor (optional)
100 A
Remote on/off
Yes
Operating temperature range
-40 to +65 °C (fan-assisted cooling). Maximum altitude 2000 m
Humidity (non-condensing)
max. 95%
Material and colour
steel, blue RAL 5012
Enclosure rating
IP22
Battery connection
M8 bolts / M8 bolts
230VAC connection
screw terminals 13 mm² (6 AWG)
Weight
20 kg
Dimensions (h × w × d)
506 × 275 × 147 mm
Safety
EN-IEC 62019-1, EN-IEC 6201-2, EN-IEC 60335-1, EN-IEC 60335-2-29
Emission / immunity
EN55014-1, EN 55014-2 EN-IEC 61000-3-2, EN-IEC 61000-3-3 / IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3
Uninterruptible power supply (UPS)
IEC 62040-1
Nominal voltage
24 V
Item number
PMP242307010
Download datasheet (PDF)
Victron EasySolar 12/1600/70-16 230V MPPT 100/50 – inverter and battery charger in one unitThe Victron EasySolar 12/1600/70-16 230V MPPT 100/50 is a combined inverter and battery charger from Victron Energy — two functions in one unit. It supplies the installation with pure sine wave 230V and automatically switches between shore power and battery operation.Advantages
PowerAssist and PowerControl: The unit supplements a weak shore power connection with battery power and prevents the campsite fuse from blowing.
Pure sine wave: The same power quality as the electrical grid — even for sensitive electronics.
Applications
Camper vans and boats where both shore power and battery operation must be managed automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage for residential and commercial use.
Specifications
Specification
Details
Nominal voltage
12 V
Weight
11 kg
Dimensions (h × w × d)
110 × 214 × 510 mm
Item number
CEP122161000
Download datasheet (PDF)
Victron EasySolar-II 48/4k5/55-32 MPPT 250/70 GX – inverter and battery charger in one unitThe Victron EasySolar-II 48/4k5/55-32 MPPT 250/70 GX is a combined inverter and battery charger from Victron Energy — two functions in one unit. It supplies the installation with pure sine wave 230V and switches automatically between shore power and battery operation.Advantages
PowerAssist and PowerControl: The unit supplements a weak shore connection with battery power, preventing the site's fuse from tripping.
Automatic transfer switch: Switches automatically between shore power and battery operation without interruption (32 A).
Pure sine wave: The same power quality as the mains — also for sensitive electronics.
Built-in GX device: Full monitoring and remote control via the VRM Portal without additional hardware.
Application
Motorhomes and boats where both shore power and battery operation must be handled automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage for residential and commercial use.
Specifications
Specification
Details
PowerControl and PowerAssist
Yes
Automatic transfer switch
32 A
Max. AC input current
32 A
Input voltage range
38 – 60 V
Output in inverter mode
output voltage: 230 VAC ± 2% Frequency: 50 Hz ± 0.1%
Cont. output power at 25°C
4 kW
Cont. output power at 40°C
3.7 kW
Cont. output power at 65°C
3 kW
Time-limited power 1 (cold start)
4.5 kW/2h
Time-limited power 2 (cold start)
6 kW/25min
Max. feed-in power
4 kW
Peak power
7 kW/1min
Max. efficiency
95%
Zero-load consumption
20 W
AC input
input voltage range: 187-265 VAC input frequency: 45–65 Hz
Charge voltage absorption
57.6 V
Charge voltage float
55.2 V
Storage mode
52.8 V
Max. battery charge current at 25°C
55 A
Max. battery charge current at 40°C
50 A
Battery temperature sensor
optional. Order number: ASS000001000
Compatible battery chemistries
Lithium, Lead-acid, Zinc-Bromine and more(3)
Auxiliary output
Yes (32 A)
External AC current sensor (optional)
100 A
Programmable relay
Yes
Protection
a - g
VE.Bus communication port
for parallel and three-phase operation, remote monitoring and system integration
General purpose communication port
Yes, 2x
Remote on/off
Yes
GX device interfaces
VE.Can, USB, Ethernet, VE.Direct, Wi-Fi
Operating temperature range
-40 to +65 °C (fan-assisted cooling).
Humidity
Maximum 95%
Max. altitude
2000 m
Model
MPPT 250/70-Tr
Max. output current
70 A
Max. PV power
4000 W
Max. PV open-circuit voltage
250 V
Self-consumption
20 mA
Material and color
steel, blue RAL 5012
Protection class
IP21
Battery connection
M8 bolts
230VAC connection
screw terminals 13 mm² (6 AWG)
Weight
28.8 kg
Dimensions (h × w × d)
591 × 275 × 254 mm
Safety
EN-IEC 62019-1, EN-IEC 6201-2, EN-IEC 60335-1, EN-IEC 60335-2-29
Emission / immunity
EN55014-1, EN 55014-2 EN-IEC 61000-3-2, EN-IEC 61000-3-3 / IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3
Uninterruptible Power Supply (UPS)
IEC 62040-1
Nominal voltage
48 V
Item number
PMP482457010
Download datasheet (PDF)
Victron EasySolar 24/1600/40 MPPT 100/50 – inverter and battery charger in one unitThe Victron EasySolar 24/1600/40 MPPT 100/50 is a combined inverter and battery charger from Victron Energy — two functions in one unit. It supplies the installation with pure sine wave 230V and switches automatically between shore power and battery operation.Advantages
PowerAssist and PowerControl: The unit supplements a weak shore connection with battery power, preventing the site fuse from blowing.
Pure sine wave: Power quality identical to the electrical grid — even for sensitive electronics.
Application
Camper vans and boats, where both shore power and battery operation must be handled automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage for residential and commercial use.
Specifications
Specification
Details
Nominal voltage
24 V
Weight
12 kg
Dimensions (h × w × d)
110 × 214 × 745 mm
Item number
CEP242161010
Download datasheet (PDF)
Victron EasySolar-II GX 48V/3000W/35A-32 MPPT 250/70 – inverter and battery charger in one unitThe Victron EasySolar-II GX 48V/3000W/35A-32 MPPT 250/70 is a combined inverter and battery charger from Victron Energy — two functions in one unit. It supplies your installation with pure sine wave 230V and switches automatically between shore power and battery operation.Benefits
PowerAssist and PowerControl: The unit supplements a weak shore power connection with battery power and prevents the fuse at the campsite or marina from blowing.
Pure sine wave: The same power quality as the mains grid — also for sensitive electronics.
Built-in GX device: Full monitoring and remote control via the VRM Portal without extra hardware.
Applications
Motorhomes and boats where both shore power and battery operation need to be handled automatically.
Off-grid and hybrid systems with solar panels and a generator.
Backup power systems and energy storage in homes and businesses.
Specifications
Specification
Details
Nominal voltage
48 V
Weight
26 kg
Dimensions (h × w × d)
237 × 268 × 499 mm
Item number
PMP482307010
Download datasheet (PDF)
Victron Quattro inverter/charger 48V/8000W/110A – inverter and battery charger in one unitThe Victron Quattro inverter/charger 48V/8000W/110A is a combined inverter and battery charger from Victron Energy — two functions in one unit. It provides the installation with pure sine wave 230V and automatically switches between shore power and battery operation.Benefits
PowerAssist and PowerControl: The unit supplements a weak shore connection with battery power and prevents the campsite fuse from blowing.
Pure sine wave: The same power quality as the electrical grid — even for sensitive electronics.
Application
Motorhomes and boats where both shore power and battery operation must be handled automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage in residential and commercial settings.
Specifications
Specification
Details
Nominal voltage
48 V
Weight
44 kg
Dimensions (h × w × d)
280 × 350 × 470 mm
Item number
QUA488024000
Download datasheet (PDF)
Victron Quattro-II 48V/5000W/70A-50/50 – inverter and battery charger in one unitThe Victron Quattro-II 48V/5000W/70A-50/50 is a combined inverter and battery charger from Victron Energy — two functions in one unit. It supplies the installation with pure sine wave 230V and automatically switches between shore power and battery operation.Advantages
PowerAssist and PowerControl: The unit supplements a weak shore power connection with battery power, preventing the site's circuit breaker from tripping.
Pure sine wave: Same power quality as the electrical grid — also for sensitive electronics.
Application
Camper vans and boats, where both shore power and battery operation must be handled automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage for residential and commercial use.
Specifications
Specification
Details
PowerControl / PowerAssist
Yes
AC input
Input frequency: 45 - 65 Hz
Max. feed-through current
50 A
Input voltage range
38 – 66 V
Output in inverter mode
Frequency: 50 Hz ± 0.1 %
Cont. output power at 25°C / 77°F
5000 VA
Cont. output power at 40°C / 104°F
3700 W
Cont. output power at 65°C / 150°F
3000 W
Max. feed-in power
5000 VA
Peak power
9000 W
Max. efficiency
96 %
Zero-load consumption
18 W
Absorption charge voltage
57.6 V
Float charge voltage
55.2 V
Storage mode
52.8 V
House battery charge current
70 A
Auxiliary output
Yes (32 A)
Programmable relay
Yes
Protection
a - g
VE.Bus communication port
for parallel and three-phase operation, remote monitoring, and system integration
General purpose com. port
Yes, 2x
Common Characteristics
Operating temp.: -40 to +65 °C (-40 – 150°F) / (fan-assisted cooling) / Humidity (non-condensing): max. 95 % / Maximum Altitude 2000 m
Material and color
steel, blue RAL 5012 / Protection category: IP21 / Pollution degree 2, OVC3
Battery connections
M8 bolts
230 VAC connections
screw terminals 13 mm² (6 AWG)
Weight
29 kg
Dimensions (h × w × d)
565 × 320 × 148 mm
Safety
EN 60335-1, EN 60335-2-29, IEC62109-1, IEC62109-2
Emission / immunity
EN 55014-1, EN 55014-2, / EN-IEC 61000-3-2, EN-IEC 61000-3-3 / IEC 61000-6-1, EN 61000-6-2, / EN 61000-6-3
Emergency power supply (UPS)
Please consult certificates on our website.
Anti-islanding
Please consult certificates on our website.
Nominal voltage
48 V
Item number
QUA482504010
Download datasheet (PDF)
Victron Quattro inverter/charger 48V/15000W/200A – inverter and battery charger in one unitThe Victron Quattro inverter/charger 48V/15000W/200A is a combined inverter and battery charger from Victron Energy — two functions in one unit. It supplies the installation with pure sine wave 230V and switches automatically between shore power and battery operation.Advantages
PowerAssist and PowerControl: The unit supplements a weak shore power connection with battery power and prevents the site fuse from blowing.
Pure sine wave: The same power quality as the grid — also for sensitive electronics.
Application
Motorhomes and boats where both shore power and battery operation must be handled automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage for residential and commercial use.
Specifications
Specification
Details
Nominal voltage
48 V
Weight
94.5 kg
Dimensions (h × w × d)
344 × 488 × 572 mm
Item number
QUA483150000
Download datasheet (PDF)
Victron Quattro inverter/charger 24V/5000W/120A – inverter and battery charger in one unitThe Victron Quattro inverter/charger 24V/5000W/120A is a combined inverter and battery charger from Victron Energy — two functions in one unit. It provides the installation with pure sine wave 230V and switches automatically between shore power and battery operation.Benefits
PowerAssist and PowerControl: The unit supplements a weak shore power connection with battery power and prevents the campsite fuse from blowing.
Pure sine wave: Same power quality as the grid — even for sensitive electronics.
Application
Motorhomes and boats, where both shore power and battery operation must be handled automatically.
Off-grid and hybrid systems with solar panels and generators.
Backup power systems and energy storage in residential and commercial settings.
Specifications
Specification
Details
Nominal voltage
24 V
Weight
33 kg
Dimensions (h × w × d)
340 × 328 × 444 mm
Item number
QUA245021010
Download datasheet (PDF)
Victron Quattro inverter/charger 12V/3000W/120A – inverter and battery charger in one unitThe Victron Quattro inverter/charger 12V/3000W/120A is a combined inverter and battery charger from Victron Energy — two functions in one unit. It supplies the installation with pure sine wave 230V and switches automatically between shore power and battery operation.Benefits
PowerAssist and PowerControl: The unit supplements a weak shore power connection with battery power and prevents the site's circuit breaker from tripping.
Pure sine wave: Same power quality as the mains — even for sensitive electronics.
Applications
Motorhomes and boats where both shore power and battery operation must be managed automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage in residential and commercial settings.
Specifications
Specification
Details
Nominal voltage
12 V
Weight
22 kg
Dimensions (h × w × d)
218 × 258 × 362 mm
Item number
QUA123020010
Download datasheet (PDF )
Victron Quattro inverter/charger 48V/10000W/140A – inverter and battery charger in one unitThe Victron Quattro inverter/charger 48V/10000W/140A is a combined inverter and battery charger from Victron Energy — two functions in one unit. It supplies the installation with pure sine wave 230V and automatically switches between shore power and battery operation.Advantages
PowerAssist and PowerControl: The unit supplements a weak shore power connection with battery power and prevents the site fuse from tripping.
Pure sine wave: Same power quality as the grid — also for sensitive electronics.
Applications
Motorhome and boat, where both shore power and battery operation must be managed automatically.
Off-grid and hybrid systems with solar panels and generator.
Emergency power systems and energy storage for residential and commercial use.
Specifications
Specification
Details
Nominal voltage
48 V
Weight
45 kg
Dimensions (h × w × d)
280 × 350 × 470 mm
Item number
QUA481030010
Download datasheet (PDF)
Victron Quattro inverter/charger 24V/8000W/200A – inverter and battery charger in one unitThe Victron Quattro inverter/charger 24V/8000W/200A is a combined inverter and battery charger from Victron Energy — two functions in one unit. It supplies the installation with pure sine wave 230V and automatically switches between shore power and battery operation.Advantages
PowerAssist and PowerControl: The unit supplements a weak shore connection with battery power and prevents the campsite fuse from blowing.
Pure sine wave: The same power quality as the electrical grid — also for sensitive electronics.
Application
Motorhomes and boats where both shore power and battery operation must be handled automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage in residential and commercial settings.
Specifications
Specification
Details
Nominal voltage
24 V
Weight
44 kg
Dimensions (h × w × d)
280 × 350 × 470 mm
Item number
QUA248020010
Download datasheet (PDF)
Victron Quattro inverter/charger 24V/3000W/70A – inverter and battery charger in one unitThe Victron Quattro inverter/charger 24V/3000W/70A is a combined inverter and battery charger from Victron Energy — two functions in one unit. It supplies the installation with pure sine wave 230V and switches automatically between shore power and battery operation.Advantages
PowerAssist and PowerControl: The unit supplements a weak shore power connection with battery power, preventing the site fuse from blowing.
Pure sine wave: The same power quality as the electrical grid — also for sensitive electronics.
Application
Campervans and boats where both shore power and battery operation must be handled automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage in residential and commercial settings.
Specifications
Specification
Details
Nominal voltage
24 V
Weight
22 kg
Dimensions (h × w × d)
218 × 258 × 362 mm
Item number
QUA243020010
Download datasheet (PDF)
Victron Quattro inverter/charger 12V/5000W/220A – inverter and battery charger in one unitThe Victron Quattro inverter/charger 12V/5000W/220A is a combined inverter and battery charger from Victron Energy — two functions in one unit. It provides the installation with pure sine wave 230V and automatically switches between shore power and battery operation.Advantages
PowerAssist and PowerControl: The unit supplements a weak shore connection with battery power, preventing the site fuse from blowing.
Pure sine wave: The same power quality as the electrical grid — even for sensitive electronics.
Application
Campervans and boats where both shore power and battery operation need to be handled automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage for residential and commercial use.
Specifications
Specification
Details
Nominal voltage
12 V
Weight
31.9 kg
Dimensions (h × w × d)
280 × 350 × 470 mm
Part number
QUA125020000
Download datasheet (PDF)
Victron Quattro 48V/5000W/70A-100/100 – inverter and battery charger in one unitThe Victron Quattro 48V/5000W/70A-100/100 is a combined inverter and battery charger from Victron Energy — two functions in one unit. It provides the installation with pure sine wave 230V and switches automatically between shore power and battery operation.Benefits
PowerAssist and PowerControl: The unit supplements a weak shore connection with battery power and prevents the campsite fuse from blowing.
Pure sine wave: Same power quality as the grid — also for sensitive electronics.
Application
Campervans and boats where both shore power and battery operation must be handled automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage for residential and commercial use.
Specifications
Specification
Details
Nominal voltage
48 V
Weight
35 kg
Dimensions (h × w × d)
240 × 328 × 444 mm
Item number
QUA485021010
Download datasheet (PDF)
Victron MultiPlus-II 48V/8000W/110/100 – inverter and battery charger in one unitThe Victron MultiPlus-II 48V/8000W/110/100 is a combined inverter and battery charger from Victron Energy — two functions in one unit. It delivers 8000 VA of pure sine wave 230V and automatically switches between shore power and battery operation.Advantages
8000 VA output power: Peak power of 15000 W for motor starting and short-term loads.
PowerAssist and PowerControl: The unit supplements a weak shore connection with battery power, preventing the site's fuse from tripping.
Pure sine wave: The same power quality as the electrical grid — even for sensitive electronics.
Application
Motorhomes and boats where both shore power and battery operation must be handled automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage for homes and businesses.
Specifications
Specification
Details
PowerControl / PowerAssist
Yes
AC input
Input voltage range: 187 - 265VAC, / Input frequency: 45 - 65 Hz
Max. feed-through current
100 A
Input voltage range
38 - 66 V
Output
Output voltage: 230VAC ± 2 % / Frequency: 50 Hz ± 0.1 %
Continuous output power at 25 °C
8000 VA
Continuous output power at 40 °C
5500 W
Continuous output power at 65 °C
4000 W
Max. feed-in power
8000 VA
Peak power
15000 W
Max. efficiency
95 %
Zero-load consumption
29 W
Charge voltage absorption
57.6 V
Charge voltage float
55.2 V
Storage mode
52.8 V
Charge current house battery
110 A
Auxiliary output
Yes (50 A)
External AC current sensor (optional)
100 A
Programmable relay
Yes
Protection
a - g
VE.Bus communication port
Three-phase and parallel(6) operation, remote monitoring and system integration
General purpose com. port
Yes, 2x
Common characteristics
Operating temp.: -40 to +65 °C (-40 – 150°F) / (fan-assisted cooling) / Humidity (non-condensing): max. 95 % / Maximum altitude: 2000 m
Material and color
Steel, blue RAL 5012 / Pollution degree 2, OVC3
Pollution degree
OVC3
Protection class
IP 22
Battery connections
Four M8 bolts (2 positive and 2 negative connections)
AC connections
Bolts M6
Weight
41.2 kg
Dimensions (h × w × d)
642 × 363 × 206 mm
Safety
EN-IEC 60335-1, EN-IEC 60335-2-29, EN-IEC 62109-1, EN-IEC 62109-2
Emission / immunity
EN 55014-1, EN 55014-2 EN-IEC 61000-3-2, EN-IEC 61000-3-3 IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3
Uninterruptible power supply (UPS)
Please consult certificates on our website.
Anti-islanding
Please consult certificates on our website.
Nominal voltage
48 V
Item number
PMP482805000
Download datasheet (PDF)
Victron Quattro-II inverter/charger 24V/5000W/120A – inverter and battery charger in one unitThe Victron Quattro-II inverter/charger 24V/5000W/120A is a combined inverter and battery charger from Victron Energy — two functions in one unit. It supplies the installation with pure sine wave 230V and automatically switches between shore power and battery operation.Benefits
PowerAssist and PowerControl: The unit supplements a weak shore connection with battery power and prevents the circuit breaker at the site from tripping.
Pure sine wave: Same power quality as the grid — even for sensitive electronics.
Application
Camper vans and boats where both shore power and battery operation must be handled automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage in homes and businesses.
Specifications
Specification
Details
PowerControl / PowerAssist
Yes
AC input
input voltage range: 187 - 265VAC
Max. feed-through current
50 A
Input voltage range
19 – 33 V
Output in inverter mode
output voltage: 230VAC ± 2 %
Cont. output power at 25°C / 77°F
5000 VA
Cont. output power at 40°C / 104°F
3700 W
Cont. output power at 65°C / 150°F
3000 W
Max. feed-in power
5000 VA
Peak power
9000 W
Max. efficiency
96 %
Zero-load consumption
18 W
Charge voltage absorption
28.8 V
Charge voltage float
27.6 V
Storage mode
26.4 V
Charge current house battery
120 A
Auxiliary output
Yes (32 A)
Programmable relay
Yes
Protection
a - g
VE.Bus communication port
for parallel and three-phase operation, remote monitoring and system integration
General purpose com. port
Yes, 2x
Common Characteristics
Operating temp.: -40 to +65 °C (-40 – 150°F) / (fan-assisted cooling) / Humidity (non-condensing): max. 95 % / Maximum Altitude 2000 m
Material and color
steel, blue RAL 5012 / Protection category: IP21 / Pollution degree 2, OVC3
Battery connections
M8 bolts
230 VAC connections
screw terminals 13 mm² (6 AWG)
Weight
31 kg
Dimensions (h × w × d)
607 × 329 × 149 mm
Safety
EN 60335-1, EN 60335-2-29, IEC62109-1, IEC62109-2
Emission / immunity
EN 55014-1, EN 55014-2, / EN-IEC 61000-3-2, EN-IEC 61000-3-3 / IEC 61000-6-1, EN 61000-6-2, / EN 61000-6-3
Emergency power supply (UPS)
Please consult certificates on our website.
Anti-islanding
Please consult certificates on our website.
Nominal voltage
24 V
Item number
QUA242505010
Download datasheet (PDF)
Victron MultiPlus-II 48/6k5/100-50 – inverter and battery charger in one unitThe Victron MultiPlus-II 48/6k5/100-50 is a combined inverter and battery charger from Victron Energy — two functions in one unit. It delivers 6 kW of pure sine wave 230V and automatically switches between shore power and battery operation.Advantages
6 kW output power: Peak power of 11 kW/1min for motor starting and short-term loads.
PowerAssist and PowerControl: The unit supplements a weak shore connection with battery power and prevents the campsite fuse from blowing.
Pure sine wave: Same power quality as the grid — also for sensitive electronics.
Applications
Camper vans and boats, where both shore power and battery operation must be managed automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage in residential and commercial settings.
Specifications
Specification
Details
PowerControl / PowerAssist
Yes
AC input
input voltage range: 187 - 265VAC
Max. feed-through current
50 A
Max. AC input current
50 A
DC input voltage range
38 - 60 V
AC output
output voltage: 230VAC ± 2 %
Continuous output power at 25 °C
6 kW
Continuous output power at 40 °C
5.7 kW
Continuous output power at 65 °C
4.6 kW
Time-limited power 1 (cold start)
6.5 kW/4h
Time-limited power 2 (cold start)
8 kW/1h
Max. feed-in power
6 kW
Peak power
11 kW/1min
Max. efficiency
96 %
Zero-load consumption
28 W
Charge voltage absorption
57.6 V
Charge voltage float
55.2 V
Storage mode
52.8 V
Max. battery charge current at 25 °C
100 A
Max. battery charge current at 40 °C
95 A
Battery temperature sensor
optional. Order number: ASS000001000
Compatible battery chemistries
Lithium, Lead-acid and more (3)
Auxiliary output
Yes (32 A)
External AC current sensor (optional)
100 A
Programmable relay
Yes
Protection
a - g
VE.Bus communication port
Three-phase and parallel operation, remote monitoring and system integration
General-purpose communication port
Yes, 2x
Operating temperature range
-40 to +65 °C (-40 – 150°F), fan-assisted cooling
Max. humidity
95 % (non-condensing)
Max. altitude
4000 m with 1 %/100 m power derating above 2000 m
Material and color
steel, blue RAL 5012
Protection class
IP 21
Battery connections
One positive M8 bolt and one negative M8 bolt
AC connections
screw terminals 13 mm² (6 AWG)
Weight
29 kg
Dimensions (h × w × d)
644 × 320 × 150 mm
Safety
EN-IEC 60335-1, EN-IEC 60335-2-29, EN-IEC 62109-1, EN-IEC 62109-2
Emission / immunity
EN 55014-1, EN 55014-2 EN-IEC 61000-3-2, EN-IEC 61000-3-3 IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3
Uninterruptible Power Supply (UPS)
IEC 62040
Anti-islanding
IEC 62116
Nominal voltage
48 V
Quantity per pallet
15 PCS
Item number
PMP482605012
Download datasheet (PDF)
Victron MultiPlus-II 12/4K/160-32 230V – inverter and battery charger in one unitThe Victron MultiPlus-II 12/4K/160-32 230V is a combined inverter and battery charger from Victron Energy — two functions in one unit. It delivers 3.4 kW of pure sine wave 230V and automatically switches between shore power and battery operation.Advantages
3.4 kW output power: Peak power of 6 kW/30s for motor starting and short-term loads.
PowerAssist and PowerControl: The unit supplements a weak shore connection with battery power and prevents the circuit breaker at the site from tripping.
Pure sine wave: The same power quality as the electrical grid — also for sensitive electronics.
Application
Camper vans and boats where both shore power and battery operation must be handled automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage in residential and commercial settings.
Specifications
Specification
Details
PowerControl / PowerAssist
Yes
AC input
Input voltage range: 187 - 265VAC
Max. feed-through current
32 A
Max. AC input current
32 A
DC input voltage range
9.5-17 V
AC output
Output voltage: 230VAC ± 2%
Continuous output power at 25 °C
3.4 kW
Continuous output power at 40 °C
3.1 kW
Continuous output power at 65 °C
2.6 kW
Time-limited power 1 (cold start)
4 kW/1h
Time-limited power 2 (cold start)
4.5 kW/2s
Max. feed-in power
3.4 kW
Peak power
6 kW/30s
Max. efficiency
93 %
Zero-load consumption
18 W
Charge voltage absorption
14.4 V
Charge voltage float
13.8 V
Storage mode
13.2 V
Max. battery charge current at 25 °C
160 A
Max. battery charge current at 40 °C
150 A
Battery temperature sensor
Yes
Compatible battery chemistries
Lithium, Lead-acid and more (3)
Auxiliary output
Yes (32 A)
External AC current sensor (optional)
100 A
Programmable relay
Yes
Protection
a - g
VE.Bus communication port
Three-phase and parallel operation, remote monitoring and system integration
General-purpose communication port
Yes, 2x
Operating temperature range
-40 to +65 °C (-40 – 150°F), fan-assisted cooling
Max. humidity
95 % (non-condensing)
Max. altitude
4000 m with 1 %/100 m power derating above 2000 m
Material and color
steel, blue RAL 5012
Enclosure class
IP 21
Battery connections
Two positive M8 bolts and two negative M8 bolts
AC connections
screw terminals 13 mm² (6 AWG)
Weight
22 kg
Dimensions (h × w × d)
576 × 276 × 164 mm
Safety
EN-IEC 60335-1, EN-IEC 60335-2-29, EN-IEC 62109-1, EN-IEC 62109-2
Emission / immunity
EN 55014-1, EN 55014-2 EN-IEC 61000-3-2, EN-IEC 61000-3-3 IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3
Uninterruptible power supply (UPS)
IEC 62040
Anti-islanding
IEC 62116
Item number
PMP122405010
Download datasheet (PDF)
Victron MultiPlus-II 48/4K5/55-32 GX – inverter and battery charger in one unitThe Victron MultiPlus-II 48/4K5/55-32 GX is a combined inverter and battery charger from Victron Energy — two functions in one unit. It provides the installation with pure sine wave 230V and switches automatically between shore power and battery operation.Advantages
PowerAssist and PowerControl: The unit supplements a weak shore connection with battery power and prevents the circuit breaker at the site from tripping.
Automatic switch: Switches automatically between shore power and battery operation without interruption (32 A).
Pure sine wave: Same power quality as the electrical grid — even for sensitive electronics.
Built-in GX device: Full monitoring and remote control via the VRM Portal without extra hardware.
Application
Motorhomes and boats where both shore power and battery operation must be managed automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage in residential and commercial settings.
Specifications
Specification
Details
PowerControl and PowerAssist
Yes
Automatic switch
32 A
Max. AC input current
32 A
Auxiliary output
Yes (32 A)
Input voltage range
38 – 60 V
Output in inverter mode
Output voltage: 230 VAC ± 2 % Frequency: 50 Hz ± 0.1 %
Cont. output power at 25°C
4 kW
Cont. output power at
3.7 kW
Cont. output power at 65°C
3 kW
Time-limited power 1 (cold start)
4.5 kW/2h
Time-limited power 2 (cold start)
6 kW/25min
Max. fed-back power
4 kW
Peak power
7 kW / 1min
Max. efficiency
95 %
Zero-load consumption
20 W
AC input
Input voltage range: 187-265 VAC Input frequency: 45 – 65 Hz
Charge voltage absorption
57.6 V
Charge voltage float
55.2 V
Storage mode
52.8 V
Max. battery charge current
55 A
Battery temperature sensor
Yes
Compatible battery chemistries
Lithium, Lead-acid, Zinc-Bromine and more (3)
Programmable (AUX) relay
Yes
Auxiliary power supply
12V / 100 mA
Programmable open collector output
70 V / 100 mA
Analog-digital aux inputs
Yes, 2x
Temperature sensor
Optional. Order number: ASS000001000
Voltage sense contacts
Yes
Protection
a - g
VE.Bus communication port
for parallel and three-phase operation, remote monitoring and system integration
General purpose communication port
Yes, 2x
Interfaces
VE.Can, USB, Ethernet, VE.Direct, Wi-Fi
External AC current sensor (optional)
100 A
Remote on/off
Yes
Operating temperature range
-40 to +65 °C (fan-assisted cooling). Maximum Altitude 2000 m
Humidity (non-condensing)
max. 95 %
Material and color
steel, blue RAL 5012
Enclosure class
IP21
Battery connection
M8 bolts
230VAC connection
screw terminals 13 mm² (6 AWG)
Weight
21.4 kg
Dimensions (h × w × d)
590 × 275 × 149 mm
Safety
EN-IEC 62019-1, EN-IEC 6201-2, EN-IEC 60335-1, EN-IEC 60335-2-29
Emission / immunity
EN55014-1, EN 55014-2 EN-IEC 61000-3-2, EN-IEC 61000-3-3 / IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3
Emergency power supply (UPS)
Certification pending
Anti-islanding
Certification pending
Item number
PMP482406000
Download datasheet (PDF)
Victron MultiPlus-II 48/6K5/100-50 GX – inverter and battery charger in one unitThe Victron MultiPlus-II 48/6K5/100-50 GX is a combined inverter and battery charger from Victron Energy — two functions in one unit. It provides the installation with pure sine wave 230V and automatically switches between shore power and battery operation.Advantages
PowerAssist and PowerControl: The unit supplements a weak shore connection with battery power and prevents the site fuse from tripping.
Automatic transfer switch: Switches between shore power and battery operation automatically without interruption (50 A).
Pure sine wave: Same power quality as the electrical grid — also suitable for sensitive electronics.
Built-in GX unit: Full monitoring and remote control via the VRM Portal without extra hardware.
Application
Motorhomes and boats where both shore power and battery operation must be managed automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage in residential and commercial settings.
Specifications
Specification
Details
PowerControl and PowerAssist
Yes
Automatic transfer switch
50 A
Max. AC input current
50 A
Auxiliary output
Yes (32 A)
Input voltage range
38 – 60 V
Output in inverter mode
output voltage: 230 VAC ± 2 % Frequency: 50 Hz ± 0.1 %
Cont. output power at 25°C
6 kW
Cont. output power at 40°C
5.7 kW
Cont. output power at 65°C
4.6 kW
Time-limited power 1 (cold start)
4.5 kW/2h
Time-limited power 2 (cold start)
8 kW/1h
Max. feed-in power
6 kW
Peak power
11 kW / 1min
Max. efficiency
96 %
Zero-load consumption
28 W
AC input
input voltage range: 187-265 VAC input frequency: 45 – 65 Hz
Absorption charge voltage
57.6 V
Float charge voltage
55.2 V
Storage mode
52.8 V
Max. battery charge current
100 A
Battery temperature sensor
Yes
Compatible battery chemistries
Lithium, Lead-acid, Zinc-Bromine and more (3)
Programmable (AUX) relay
Yes
Auxiliary power supply
12V / 100 mA
Programmable open collector output
70 V / 100 mA
Analog-digital aux inputs
Yes, 2x
Temperature sensor
optional. Order number: ASS000001000
Voltage sense contacts
Yes
Protection
a - g
VE.Bus communication port
for parallel and three-phase operation, remote monitoring and system integration
General purpose communication port
Yes, 2x
Interfaces
VE.Can, USB, Ethernet, VE.Direct, Wi-Fi
External AC current sensor (optional)
100 A
Remote on/off
Yes
Operating temperature range
-40 to +65 °C (fan-assisted cooling). Maximum Altitude 2000 m
Humidity (non-condensing)
max. 95 %
Material and color
steel, blue RAL 5012
Protection class
IP21
Battery connection
M8 bolts
230VAC connection
screw terminals 13 mm² (6 AWG)
Weight
29.0 kg
Dimensions (h × w × d)
644 × 320 × 150 mm
Safety
EN-IEC 62019-1, EN-IEC 6201-2, EN-IEC 60335-1, EN-IEC 60335-2-29
Emission / immunity
EN55014-1, EN 55014-2 EN-IEC 61000-3-2, EN-IEC 61000-3-3 / IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3
Emergency power supply (UPS)
Certification pending
Anti-islanding
Certification pending
Item number
PMP482606000
Download datasheet (PDF)
Victron MultiPlus-II 48V/10000W/140-100 – inverter and battery charger in one unitThe Victron MultiPlus-II 48V/10000W/140-100 is a combined inverter and battery charger from Victron Energy — two functions in one unit. It delivers 10000 VA pure sine 230V and automatically switches between shore power and battery operation.Advantages
10000 VA output power: Peak power of 18000 W for motor starting and short-term loads.
PowerAssist and PowerControl: The unit supplements a weak shore connection with battery power, preventing the site's fuse from tripping.
Pure sine wave: The same power quality as the electrical grid — even for sensitive electronics.
Application
Motorhomes and boats, where both shore power and battery operation must be handled automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage for residential and commercial use.
Specifications
Specification
Details
PowerControl / PowerAssist
Yes
AC input
Input voltage range: 187 - 265VAC, / input frequency: 45 - 65 Hz
Max. feed-through current
100 A
Input voltage range
38 - 66 V
Output
Output voltage: 230VAC ± 2 % / frequency: 50 Hz ± 0.1 %
Continuous output power at 25 °C
10000 VA
Continuous output power at 40 °C
7000 W
Continuous output power at 65 °C
6000 W
Max. feed-in power
10000 VA
Peak power
18000 W
Max. efficiency
95 %
Zero-load consumption
38 W
Charge voltage absorption
57.6 V
Charge voltage float
55.2 V
Storage mode
52.8 V
Charge current house battery
140 A
Auxiliary output
Yes (50 A)
External AC current sensor (optional)
100 A
Programmable relay
Yes
Protection
a - g
VE.Bus communication port
Three-phase and parallel (6) operation, remote monitoring and system integration
General purpose com. port
Yes, 2x
Common characteristics
Operating temp.: -40 to +65 °C (-40 – 150°F) / (fan-assisted cooling) / Humidity (non-condensing): max. 95 % / Maximum altitude: 2000 m
Material and color
steel, blue RAL 5012 / Pollution degree 2, OVC3
Pollution degree
OVC3
Protection class
IP 22
Battery connections
Four M8 bolts (2 positive and 2 negative connections)
AC connections
Bolts M6
Weight
48.8 kg
Dimensions (h × w × d)
677 × 363 × 206 mm
Safety
EN-IEC 60335-1, EN-IEC 60335-2-29, EN-IEC 62109-1, EN-IEC 62109-2
Emission / immunity
EN 55014-1, EN 55014-2 EN-IEC 61000-3-2, EN-IEC 61000-3-3 IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3
Uninterruptible power supply (UPS)
Please consult certificates on our website.
Anti-islanding
Please consult certificates on our website.
Nominal voltage
48 V
Part number
PMP483105000
Download datasheet (PDF)
Victron MultiPlus inverter/charger 48V/5000W/70A – inverter and battery charger in one unitThe Victron MultiPlus inverter/charger 48V/5000W/70A is a combined inverter and battery charger from Victron Energy — two functions in one unit. It supplies the installation with pure sine wave 230V and automatically switches between shore power and battery operation.Benefits
PowerAssist and PowerControl: The unit supplements a weak shore connection with battery power, preventing the site's fuse from blowing.
Pure sine wave: Power quality identical to the grid — even for sensitive electronics.
Application
Motorhomes and boats where both shore power and battery operation must be handled automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage in residential and commercial settings.
Specifications
Specification
Details
Nominal voltage
48 V
Weight
35 kg
Dimensions (h × w × d)
240 × 328 × 444 mm
Item number
PMP485021010
Download datasheet (PDF)
Victron MultiPlus inverter/charger 48V/500W/6A – inverter and battery charger in one unitThe Victron MultiPlus inverter/charger 48V/500W/6A is a combined inverter and battery charger from Victron Energy — two functions in one unit. It provides the installation with pure sine wave 230V and automatically switches between shore power and battery operation.Benefits
PowerAssist and PowerControl: The unit supplements a weak shore power connection with battery power, preventing the site's fuse from blowing.
Pure sine wave: The same power quality as the electrical grid — even for sensitive electronics.
Application
Camper vans and boats where both shore power and battery operation need to be handled automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage for residential and commercial use.
Specifications
Specification
Details
Nominal voltage
48 V
Weight
4.4 kg
Dimensions (h × w × d)
100 × 181 × 311 mm
Item number
PMP481500000
Download datasheet (PDF)
Victron MultiPlus inverter/charger 48V/800W/9A – inverter and battery charger in one unitThe Victron MultiPlus inverter/charger 48V/800W/9A is a combined inverter and battery charger from Victron Energy — two functions in one unit. It provides the installation with pure sine wave 230V and automatically switches between shore power and battery operation.Advantages
PowerAssist and PowerControl: The unit supplements a weak shore power connection with battery power and prevents the site fuse from blowing.
Pure sine wave: The same power quality as the electrical grid — even for sensitive electronics.
Application
Motorhome and boat, where both shore power and battery operation must be handled automatically.
Off-grid and hybrid systems with solar cells and generator.
Emergency power systems and energy storage in residential and commercial settings.
Specifications
Specification
Details
Rated voltage
48 V
Weight
7.5 kg
Dimensions (h × w × d)
100 × 240 × 360 mm
Item number
PMP481800000
Download datasheet (PDF)
Victron MultiPlus inverter/charger 48V/1600W/13A – inverter and battery charger in one unitThe Victron MultiPlus inverter/charger 48V/1600W/13A is a combined inverter and battery charger from Victron Energy — two functions in one unit. It supplies the installation with pure sine wave 230V and automatically switches between shore power and battery operation.Advantages
PowerAssist and PowerControl: The unit supplements a weak shore connection with battery power and prevents the site fuse from blowing.
Pure sine wave: The same power quality as the electrical grid — even for sensitive electronics.
Application
Motorhomes and boats where both shore power and battery operation must be handled automatically.
Off-grid and hybrid systems with solar panels and generators.
Emergency power systems and energy storage in residential and commercial settings.
Specifications
Specification
Details
Nominal voltage
48 V
Weight
11.5 kg
Dimensions (h × w × d)
120 × 270 × 465 mm
Part number
PMP482160000
Download datasheet (PDF)
Victron MultiPlus 48V/3000W/35A-50 – inverter and battery charger in one unitThe Victron MultiPlus 48V/3000W/35A-50 is a combined inverter and battery charger from Victron Energy — two functions in one unit. It supplies your installation with pure sine wave 230V and switches automatically between shore power and battery operation.Benefits
PowerAssist and PowerControl: The unit supplements a weak shore power connection with battery power and prevents the fuse at the campsite or marina from blowing.
Pure sine wave: The same power quality as the mains grid — also for sensitive electronics.
Applications
Motorhomes and boats where both shore power and battery operation need to be handled automatically.
Off-grid and hybrid systems with solar panels and a generator.
Backup power systems and energy storage in homes and businesses.
Specifications
Specification
Details
Nominal voltage
48 V
Weight
20 kg
Dimensions (h × w × d)
218 × 258 × 362 mm
Item number
PMP483021010
Download datasheet (PDF)
Victron MultiPlus 48V/3000W/35A-16 – inverter and battery charger in one unitThe Victron MultiPlus 48V/3000W/35A-16 is a combined inverter and battery charger from Victron Energy — two functions in one unit. It supplies your installation with pure sine wave 230V and switches automatically between shore power and battery operation.Benefits
PowerAssist and PowerControl: The unit supplements a weak shore power connection with battery power and prevents the fuse at the campsite or marina from blowing.
Pure sine wave: The same power quality as the mains grid — also for sensitive electronics.
Applications
Motorhomes and boats where both shore power and battery operation need to be handled automatically.
Off-grid and hybrid systems with solar panels and a generator.
Backup power systems and energy storage in homes and businesses.
Specifications
Specification
Details
Nominal voltage
48 V
Weight
20 kg
Dimensions (h × w × d)
218 × 258 × 362 mm
Item number
PMP483020001
Download datasheet (PDF)
